URGENT: Insert MPC2000XL DISK!

MisterK wrote:I know..I know..I've already read other topics..It's a real ****.
Yesterday I've installaed a PCD-47 , and all was Ok with vers. 1.14. Later I tried to update the OS to 1.20 , and my lovlely MPC2000Xl gave me the error after reboot.
, I'm producing my beats and I've to finish my works..
Please, give a great recovery procedure, the instruction for a cold boot, tell me something to make on line my MPC.
But , if I put the OS file on the card reader, why MPC doesn't boot?
I've to set the SCSI ID to zero?
Help me, it's important.

MisterK wrote:Roan,
It works.
I've had to use the floppy to perform tha flash job again,and then reconnect the CardReader.
With 1.14 my 2KXL works perfect!
Thanks a lot.[/url]

mpc3000le wrote:

MisterK wrote:I know..I know..I've already read other topics..It's a real ****.
Yesterday I've installaed a PCD-47 , and all was Ok with vers. 1.14. Later I tried to update the OS to 1.20 , and my lovlely MPC2000Xl gave me the error after reboot.
, I'm producing my beats and I've to finish my works..
Please, give a great recovery procedure, the instruction for a cold boot, tell me something to make on line my MPC.
But , if I put the OS file on the card reader, why MPC doesn't boot?
I've to set the SCSI ID to zero?
Help me, it's important.

Another case of a corrupted boot ROM.

The reason your MPC2000XL isn't able to boot from the SCSI device is because it was never told to and in it's brain dead state the box is still looking for or rather falling back to the floppy drive.

Pull out the PCD-47B. Re-connect the floppy. Stick a floppy into the drive containing the OS.BIN file. Let the machine boot. Re-perform the flash process. Remove the floppy. Put the PCD-47B back into the machine.

All should be good.
I think I get the situation that I need a recovery chip？What 's the recovery chip？I never heard abou it

If this doesn't work then PM me as you may need a recovery chip fitted in order to clean flash the whole OS flash area.

Rohan.

JUKE 179r wrote:Rohan is still around but sadly not on any music forums anymore. He's mostly on Australian Land Rover forums.

JUKE 179r wrote:Rohan is still around but sadly not on any music forums anymore. He's mostly on Australian Land Rover forums.

richie wrote:

JUKE 179r wrote:Rohan is still around but sadly not on any music forums anymore. He's mostly on Australian Land Rover forums.

Apparently he's aided in a new Vimana build for this filter kit that Jazzcat may still be working on for the 60.

cleansocks wrote:
man. I really can't believe he just dipped out like that. I saw his posts and he really did look like a decent dude helping people out. Tossed that cuz over pirated chips? I mean , I'd be mad too but not at the whole community I've been tied to for years. I'm new af to these forums so i don't really have that knowledge, just been reading a lot and concluded that stunt was kinda **** of him. Easy to say with hindsight but it's still funny seeing all those ppl rush to defend him "nah hes a good dude hes coming back" . Just goes to show even the best of us are susceptible to switchin up

Beatdiggerjazzcat wrote:That's news to me

richie wrote:

Beatdiggerjazzcat wrote:That's news to me

Weren't you the one showing off that low pass filter mod for the mpc 60 on facebook?

Am I mistaken or did I not see a picture and words in the comments about a build above 3.15 which was said to have some sort of parameters for automating the filter through the graphical interface?

Beatdiggerjazzcat wrote:yes that's me mate, but i edited the os to go with the filter, its only a basic edit and nothing fancy. would love to have done a project with Rohan though.