Post your questions, opinions and reviews of the MPC1000. This forum is for discussion of the OFFICIAL Akai OS (2.1). If you wish to discuss the JJ OS, please use the dedicated JJ OS forum
User avatar
By NeckUno1 Mon Mar 19, 2012 7:52 am
Hi everyone!
I`m a new member of this forum. I have bought used MPC1000v2 (it was damaged, but i have repaired it myself, I will post instructions how to but later). I was wondering is it possible to connect a hard drive to MPC without this f.....g adapter which price is to big for a piece of **** metal :) And I have a one question. Does anybody tried this?
All we need it`s just standard 44 or 50-pin cable for 2,5" HDD and soldering iron to connect it to the PCB of MPC.

I have prepared the comparison of pins in the machine and the pinouts of HDD.

Sorry for my english, i`m from Poland.


Last edited by NeckUno1 on Fri Mar 23, 2012 8:10 am, edited 1 time in total.
User avatar
By NeckUno1 Fri Mar 23, 2012 8:07 am
The price of HDM-10 kit in Poland is around 40$ and 44-Pin IDE cable is 6$ so I think it`s worth it because the rest of money I will spend on some other stuff e.g HDD. Also the way to do isn`t hard for me because I love to mod/repair electronic stuff myself. I just asked is somebody does something similar and is it worked?
By mcschippenhorst Wed Oct 24, 2018 8:54 am
Yeah for me it was the challenge to overcome this dependency to MPC Stuff and the 40€ shipping to Germany....
At the end with all that trying it may have cost me the dame or more :-) but i´m happy to know that my Diy Adapter works....hihi

Okidoke so the things you need (if you do it like me. Different solutions are possible) are

- 3M MDR ( Mini Delta Ribbon) Female Connector with 50 Pins. / But you have to remove the metal bracket.(easy)
- a ATA ribbon cable 50 wires / that you will have to divide in the middle and connect the first 25 to one side of the MDR IDC CRIMPS and the other 25 to the other side

-a 44 pin/hole PATA 2m pitch connector. / ( I cut one out from a old external 2,5" harddisk usb cases PCB)

You could take the MDR PCB mount style like on the MPC male side or like i did the IDC Ribbon style connector. I Crimped it in my vise ;-) ( Careful it can easyly break )

Part Number is

3M 10250-0210EC ( IDC Version)

I also found a non shielded after i ordered one

3M 10150-8000EE

And here the PCB mount style

3M 10250-55H3PC


3M 10250-52A2

there are nultiple versions that all should fit the male connector on the MPC side (with removed metal case)

You also might wanna check out that pcb brakout board. But it´s a bit pricy


So and then you have the PIN Diagramm.

The service manual says this:

But as i measured with my multimeter that is not correct.

what i measured looks like this ( it works for me but no guarantee! please double check. Maybe there are differences between the MPC1000 models)


You can now use a PATA 44 Pin Drive oder an SD Card adapter like this one in the Video

Hope that helps so far and if there is anything to ask... ask it.

have a nice day
By nrrrd Wed Oct 24, 2018 7:32 pm
Danke schön, @mcschippenhorst, that's all really useful.
The difference between what you've done and the MPCstuff adapter and the official pin out is that they both use a 50pin IDE connector and you have used a 44pin IDE connector. Could this explain the difference in the pin outs? In the video above the first 3 pins are unused. I'll have to study the pin out diagrams above to determine whether this lines up with what you've done.

Thanks for all the info
By mcschippenhorst Wed Oct 24, 2018 8:48 pm
Hi the difference is that the conversion takes place directly via the cables. No extra PCB.

The uncorrect PIN out makes sense in a way that they bundled them in Groups. I realized that when i manually soldered all the cables.
actually the order is aleady on the MPC HDD Connector in this fashion. I just didn´t mark it in my JPG.
I simply didn´t have a 50 hole connector flying around. If you look close in the Video the first 6 pins are not in use. (The 4 Master and Slave select Pins are not used plus the empty ones you normally have in the PATA connector.) You can see it in the shematics of the PATA HDD.
As well as the others where i did not put in red text. They are also NC not connected.
only 39 of the 42 from the board coming are used.
So i used an old one i had around.