STILL GETTING CLICKS AFTER OS 1.05

Post your questions, opinions and reviews of the MPC1000. This forum is for discussion of the OFFICIAL Akai OS (2.1). If you wish to discuss the JJ OS, please use the dedicated JJ OS forum
 Reply Share on Facebook
User avatar

STILL GETTING CLICKS AFTER OS 1.05

By loo2004ep Fri Sep 03, 2004 8:39 am
STILL GETTING CLICKS DURING SEQUENCES WHILE IM PLAYIN THEM,THIS IS A WHORE OF A PROBLEM, I PRETTY MUCH CANT MAKE ANY BEATS AS LONG AS I CAN HEAR THIS SHIT ,I PLAYED EVERY SAMPLE IN ALL MY BANKS AND LISTENED CLOSELY NO CLICKS AT THE END OR BEGINNING OF ANY OFTHEM ,YET WHEN I PLAY THE SEQUENCE I GET CLICKSAT AWKWARD POINTS, THIS IS BULLSHIT IM GUNNA TRY TO RETURN THIS SHIT (IF I STILL CAN) AND GO FOR ANOTHER PRODUCT
User avatar

By dubnov Fri Sep 03, 2004 9:02 am
Loo, is your compressor on? I get clicks when I use low compressor gain settings.
User avatar

By loo2004ep Fri Sep 03, 2004 9:25 am
yup even wit the comptessor off it happens
User avatar

By big_m Fri Sep 03, 2004 6:37 pm
in trim mode i noticed when you go to the loop mode or whatever and play it it will give it a click but when i stay out of the loop mode it goes fine. there two buttons trim and loop in trim mode if you dotn ever press that loop button or f2 or soemhtign you wont get clicks at least i dont.
User avatar

By loo2004ep Sat Sep 04, 2004 12:33 am
seriously yo what a piece of shlt,this thing got more bugs than the projects

By JStruMENTAL Sat Sep 04, 2004 3:22 am
ahahahahahhahaa

lick the clicks

ByMr. Hustler Sat Sep 04, 2004 3:35 am
Do what homie said about turning off loop in trip mode.
I had the same problem w/ 1 bar .WAV loops until I disabled
loop in trim mode. Just use the loop feature in trim mode to make sure you chopped it up right, so that it's sample-accurate. When it loops right, turn it off and BANG, no more sh***y-ass clicks in sequences or songs.

Mr. Hustler
New Mexico[/url]
User avatar

By loo2004ep Sat Sep 04, 2004 4:44 am
loop:off

clicks still there
User avatar

By AMG Sun Sep 12, 2004 10:20 pm
I got a click after importing a .wav from CEP. I was looping the sample.

By kon Tue Sep 14, 2004 11:20 am
how about adjusting the attack and decay of the samples?
User avatar

By loo2004ep Tue Sep 14, 2004 4:30 pm
i reimported the same samples and shut loop off and the clicks went away, fukin weird shlt

By tdot Tue Sep 14, 2004 5:30 pm
the only time I've ever(once or twice) gotten clicks is when the sample wasn't chopped enough or was cut down too much..

I guess I have a good 1000 :)
User avatar

By beyondhope1 Tue Sep 14, 2004 7:51 pm
tdot wrote:the only time I've ever(once or twice) gotten clicks is when the sample wasn't chopped enough or was cut down too much..

I guess I have a good 1000 :)


Haha. Same here man. I read all about this clicking but the only time i notice a click is if my sample is to long or to short.
User avatar

By heavysound Tue Sep 14, 2004 10:41 pm
Yes i used to get the clicks on occasion.
As I have previously mentioned..... sometimes the click is not noticeable until exiting trim mode and hitting the pads in main mode. To fix it I just go back into trim and shorten (or lengthen) the sample start and/or end. Then I listen in MAIN not trim to hear the changes etc...

Seems like lots of complainers on here. Even with glitches, the MPC is pretty ill for the $. I used to mess with beats on the Ensoniq EPS and I always got crazy clicks and there was no luxury of being able to see the waveform so it was all by ear etc.. I used to think that it was the biggest pain in the ass and I would constantly get frustrated. But then I would consider how many producers used the EPS and made full albums etc.. Wu-Tang, Nonce, etc...

So I think it's not the machine so much as it is the operator.
Patience and technique is key.
Peace,
Al
 Reply
Return to MPC1000