By wudsiba
Fri Jun 12, 2009 2:30 am
----------------------------------------------
Bug Fixes: OS2XL Ver1.15 12-JUN-2009
----------------------------------------------
Notes: If Input thru is turned ON, when a strange character will be displayed on the value of a parameter (or it may freeze)
It will be repaired if a power supply is switched on pressing the ERASE key.
1. [DRUM GRID]
F2[COPY]+[BAR >]
It does not work.
2. Mono sample will not crossfaded in playback.
3. [AUDIO TRACK]
[PAD LOCATE]
It does not memorize.
This value is memorized by the sequence.
4. [PROGRAM]
Behavior of cursor is strange when changing a track.
5.[GRID]
[TIME SHIFT]
After moving by [SHIFT]+[BAR<>] Strange, when Time Shift is performed.
<Addition>
1. Change of a sequence can be performed if a DATA wheel is turned pressing a pad. (It cannot do during recording and playback)
2. [DRUM PROGRAM]
[SIMULT PAD]( F5[LFO:MUTE] )
The mode which does not record simult PAD was added.
SIMULT1: simult PAD is recorded.
SIMULT2: simult PAD is not recorded. (In the case of SIMULT2, Q-Link works only to the pad of a master.)
Refer to manual.
<Change>
Work of PAD at the time of start end point adjustment of TRIM was changed as follows.
PAD9-PAD12 work, as shown in the following figure.
If PAD1-PAD4 is hit, a sample will be plays by NOTE ON. (St<-->End note on play)
If PAD5-PAD8 is hit, a sample will be plays by ONE SHOT. (St<-->End one shot play)
Moreover, a start or an end point can be adjusted, carrying out audition, if a DATA wheel is turned
pressing a pad (PAD1-PAD4 and PAD9-PAD12).
If PAD1, PAD2, PAD5, PAD6, PAD9, and PAD10 are pressed, cursor will move to St field.
If PAD3, PAD4, PAD7, PAD8, PAD11, and PAD12 are pressed, cursor will move to End field.
If PAD9-PAD12 and PAD14-PAD16 are pressed, the waveform of a play portion will blink.
It works similarly on the screen of F5 (CHOP).
In the case of Non-Destructive Chop ON
When cursor is in the End field, the same play as above figure PAD11 is carried out.
Bug Fixes: OS2XL Ver1.15 12-JUN-2009
----------------------------------------------
Notes: If Input thru is turned ON, when a strange character will be displayed on the value of a parameter (or it may freeze)
It will be repaired if a power supply is switched on pressing the ERASE key.
1. [DRUM GRID]
F2[COPY]+[BAR >]
It does not work.
2. Mono sample will not crossfaded in playback.
3. [AUDIO TRACK]
[PAD LOCATE]
It does not memorize.
This value is memorized by the sequence.
4. [PROGRAM]
Behavior of cursor is strange when changing a track.
5.[GRID]
[TIME SHIFT]
After moving by [SHIFT]+[BAR<>] Strange, when Time Shift is performed.
<Addition>
1. Change of a sequence can be performed if a DATA wheel is turned pressing a pad. (It cannot do during recording and playback)
2. [DRUM PROGRAM]
[SIMULT PAD]( F5[LFO:MUTE] )
The mode which does not record simult PAD was added.
SIMULT1: simult PAD is recorded.
SIMULT2: simult PAD is not recorded. (In the case of SIMULT2, Q-Link works only to the pad of a master.)
Refer to manual.
<Change>
Work of PAD at the time of start end point adjustment of TRIM was changed as follows.
PAD9-PAD12 work, as shown in the following figure.
If PAD1-PAD4 is hit, a sample will be plays by NOTE ON. (St<-->End note on play)
If PAD5-PAD8 is hit, a sample will be plays by ONE SHOT. (St<-->End one shot play)
Moreover, a start or an end point can be adjusted, carrying out audition, if a DATA wheel is turned
pressing a pad (PAD1-PAD4 and PAD9-PAD12).
If PAD1, PAD2, PAD5, PAD6, PAD9, and PAD10 are pressed, cursor will move to St field.
If PAD3, PAD4, PAD7, PAD8, PAD11, and PAD12 are pressed, cursor will move to End field.
If PAD9-PAD12 and PAD14-PAD16 are pressed, the waveform of a play portion will blink.
It works similarly on the screen of F5 (CHOP).
In the case of Non-Destructive Chop ON
When cursor is in the End field, the same play as above figure PAD11 is carried out.
wudsiba
Mp1k JJos2/2xl
Mp1k JJos2/2xl
!!!!