jjos2 onboard synthesizer tips: a sampler IS a synth

eimer wrote:Ja, lad os alle skrive på hvert vores modersmål så ingen fatter hvad vi skriver. Det er sku' det mest geniale jeg nogensinde har set på et offentligt forum. Hold da kæft!

sally wrote:

eimer wrote:Ja, lad os alle skrive på hvert vores modersmål så ingen fatter hvad vi skriver. Det er sku' det mest geniale jeg nogensinde har set på et offentligt forum. Hold da kæft!

Querido eimer, por mi parte no hay problema en cuanto a lo que tu expones, yo por ejemplo, haria uso del traductor y creo que te has explicado muy bien y yo te he entendido perfectamente.
Es mas aun, hace tiempo, hubo gente del foro, que me pidio que yo me expresara en mi lengua materna.
Debio de parecerles muy interesante las cosas que yo argumentaba... Y asi lo hice, y hoy mismo he escrito varios post, y hasta el momento, desde los moderadores de este foro, y doy gracias a ellos, pues todavia no me han dicho que deje de hacerlo.
Por tanto... No se que mas quieres que te diga,

Que... Se acerca mi cupo de post escritos en este foro?
No, todavia no, aunque pronto hare mi cupo, soy consciente de ello.

Saludos.

Lampdog wrote:[color=gold]
With note repeat, you'd be re-triggering at every note repeat event wouldn't you?

Looping a single cycle and then using envelope, lfo, osc, asdr tools would be more efficient for synth tools riding realtime through the loop I would think.

sally wrote:BUMP!!!

Turn on my MPC.
Press mode + pad 5 ( Go to Record )
Select: Analog Input
Press press F6 ( Start Record a few seconds/moments for sample1 ) = Recording Noise for sample1



Ok

Go to Trim mode ( mode + pad 6 )

With sample1
EDIT: Normalize 100% for example.




Now
use extract for obtain sample2 ( half of single cycle wave) and sample3 (other half of single cycle wave)

Select containing wave start point L chanel for 00000000 and end point 00000001 = extract for obtain sample2

Select containing wave start point R chanel for 00000000 and end point 000000001 = extract for obtain sample3

Ok ?!!!

Now
Go to Trim edit Combine A + B








Sample2 + Sample3 = sample4 = SINGLE CYCLE

Sample2 + Sample3 = Sample4 = 00000002 end point ( lenght of the sample, view on TRIM mode )



Sample4 + sample4 = sample5 = 00000004 end point
SINGLE CYCLE + SINGLE CYCLE = TWO CYCLES



Sample5 + sample5 = sample6 = 00000008 end point



REPEAT SOMETIME
Sample.... + sample........ = xxxxxxxxxx end point

Sample.... + sample........
= 00000016 end point
Sample.... + sample........
= 00000032 end point
Sample.... + sample........
= 00000064 end point
S
= 00000128 end point
S
= 00000256 end point
S
= 00000512 end point
S
= 00001024 end point
S
= 00002048 end point
S
= 00004096 end point
S
= 00008192 end point
S
= 00016384 end point
S
= 00032868
Sample18 + sample18 = sample19
= 00065736 end point




Now, select sample19 start point 00000000 and end point 44100 and discard ( trim edit )


The result is a sample with 22.050 hz (-herz-) CYCLES per seconds, you see this TONE/NOTE is square Wave, also Sine wave is very possible , other TONES/NOTES and much more!

Now, you know it!!
We can make a WaveForm with....

sally wrote: single cycle not be enough.

sally wrote:

Nym wrote:your lengths: 44100,

44100 = 1 second audio long sample = 44100 Hz too = Hz / seconds.